Raritan PX-1000 Series Guide de l'utilisateur Page 173
- Page / 258
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 7: Using the Command Line Interface
161
Note: After determining the format for the Z coordinate, you can set a
value for it. See Setting the Z Coordinate (on page 181).
Example
The following command determines that the unit of rack is used for
specifying the Z coordinate of environmental sensors.
config:# pdu externalSensorsZCoordinateFormat rackUnits
Networking Configuration Commands
A number of network settings can be changed through the CLI, such as
the IP address, transmission speed, duplex mode, and so on.
Setting the Networking Mode
If your Dominion PX device is implemented with both of the wired and
wireless networking mechanisms, you must determine which mechanism
is enabled for network connectivity before further configuring networking
parameters.
This command syntax enables the wired or wireless networking mode.
config:# networkingMode <mode>
Variables:
<mode> is one of the modes: wired or wireless.
Mode Description
wired Enables the wired networking mode.
wireless Enables the wireless networking mode.
Note: If you enable the wireless networking mode, and Dominion PX does
not detect any wireless USB LAN adapter or the connected wireless USB
LAN adapter is not supported, the message "Supported Wireless device
not found" is displayed.
Example
The following command enables the wired networking mode.
config:# networkingMode wired
- PX-1000 Series 1
- Safety Guidelines 2
- Safety Instructions 3
- FCC Information 4
- VCCI Information (Japan) 4
- Contents 7
- Contents 10
- Applicable Models 11
- Chapter 1 13
- Introduction 13
- Package Contents 14
- Chapter 1: Introduction 15
- Chapter 2 16
- Rack-Mounting the PDU 16
- Mounting 1U or 2U Models 19
- Chapter 3 22
- Configuring Dominion PX 25
- Contact Closure Sensor LEDs 36
- Chapter 4 40
- Using the PDU 40
- Chapter 4: Using the PDU 41
- Chapter 4: Using the PDU 42
- Three-Digit Row 43
- Two-Digit Row 44
- LEDs for Measurement Units 44
- Automatic Mode 45
- Manual Mode 45
- Circuit Breakers 46
- Chapter 5 49
- Using the Web Interface 49
- Expanding the Tree 55
- Collapsing the Tree 56
- Adjusting the Pane 56
- Warning Icon 59
- Changing the View of a List 60
- Changing the Column 60
- Changing the Sorting 61
- Resizing a Dialog 61
- Viewing the Dashboard 63
- Device Management 63
- Role of a DNS Server 67
- Wired Network Settings 67
- Wireless Network Settings 68
- Changing the SSH Settings 69
- Changing the Telnet Settings 70
- How to Use the Calendar 73
- Enabling Data Logging 74
- User Management 76
- Setting Up Roles 80
- Access Security Control 84
- Enabling the Firewall 85
- Changing the Default Policy 85
- Creating Firewall Rules 86
- Editing Firewall Rules 88
- Sorting Firewall Rules 88
- Deleting Firewall Rules 88
- Enabling User Blocking 89
- Enabling Login Limitations 90
- Enabling Strong Passwords 90
- Enabling Password Aging 91
- Enabling the Feature 92
- Outlet Management 105
- Setting Power Thresholds 110
- Configuring Event Rules 114
- Creating Actions 115
- Creating Rules 116
- Sample PDU-Level Event Rule 118
- Managing Event Logging 122
- Viewing Connected Users 123
- Environmental Sensors 125
- Sensor Measurement Accuracy 131
- States of Managed Sensors 131
- "normal" State 132
- "alarmed" State 133
- Asset Management 134
- Network Diagnostics 140
- Firmware Upgrade 143
- Using SNMP 144
- Accessing the Help 145
- Chapter 6 148
- Downloading 149
- SNMP MIB 149
- Configuring SNMP Traps 150
- SNMP Gets and Sets 151
- Chapter 6: Using SNMP 152
- SNMP Sets and Thresholds 153
- Chapter 7 154
- Help Command 157
- Showing Information 158
- Changing the PDU Name 171
- Example 171
- Setting the Networking Mode 173
- Setting the SSID 174
- Setting the PSK 174
- Setting the BSSID 175
- Changing the LAN Duplex Mode 176
- Setting the IP Address 177
- Setting the Subnet Mask 178
- Setting the Gateway 178
- Changing the HTTP Port 180
- Changing the HTTPS Port 181
- IP Access Control 181
- HTTPS Access 184
- Login Limitation 185
- User Blocking 186
- Strong Passwords 187
- Changing the Outlet Name 190
- Changing the Inlet Name 190
- Changing the Sensor Name 191
- Setting the X Coordinate 192
- Setting the Y Coordinate 192
- Setting the Z Coordinate 193
- Commands for Inlet Sensors 194
- Creating a User Profile 216
- Modifying a User Profile 217
- Deleting a User Profile 222
- Changing Your Own Password 223
- Creating a Role 223
- Modifying a Role 224
- Deleting a Role 226
- Unblocking a User 228
- Resetting Dominion PX 228
- Network Troubleshooting 229
- Retrieving Previous Commands 232
- Logging out of CLI 233
- Appendix A 234
- Specifications 234
- Appendix B 236
- Equipment Setup Worksheet 236
- Appendix C 240
- MAC Address 240
- Appendix D 241
- Appendix E 249
- Using the CLI Command 250
- Appendix F 252
- Attached 252
- Index 255
© 2020, manymanuals.fr. Tous droits réservés | 1.008 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels